| Sculling boat makes progress |
|
|
|
| Written by Jon | |||
| Tuesday, 17 February 2009 15:13 | |||
|
So despite my silence I have actually been doing some work as I find the time on the light sculling trainer. The boat is about 16 feet long, and just shy of a 2 foot beam. I downloaded the hull files from Hannu's Boatyard. Initially I started this project as an inexpensive project I could complete quickly. Well it has been cheap, and I haven't spent more than about 20 hours on it so far, but that has been over the past year.
I had no passion for the build so I would never make time to work on it. Now I have a renewed desire to have another kayak as well as my initial desire for a sculling boat, so I am spending more time on it. ![]() I learned quite a bit about building during this project, the 2 big things being, I like any part of the project dealing with hand tools and that I don't like working with epoxy and glass. The more bits that I work on using hand tools, the more I "find" time to work on the boat. That little gem will surely influence my choice of future project.
![]() I know the shot above looks warped, but it is not. The stern was quite fun to shape.
![]() You may notice the black markers arrows all over the hull. I found it was really easy to look over the hull and mark screw holes and other low spots that needed filling with thickened epoxy. That really helped extend the small batches of goo I made to fill those holes, since I could quickly locate each area and be done before the goo went off.
![]() Yes, I have some wobble in my panels. Why? well I didn't use a batten when drawing the sides and bottom panels. I just connected the dots from the hull file. Not a huge deal, but next time I know better and will have a nicer looking chine.
![]() Inwales are glued in using Titebond III. It is so much easier to use than epoxy, and fine for this purpose on a recreational day boat.
![]() The bow and stern decks will be 5.2mm luan underlayment, and I wanted them to fit into the inwales flush. So in the cockpit, I raised the inwales 1/4 inch, then I used my pull saw to trim the fore and aft inwales flush. I really enjoyed this process, and WOW does that pull saw cut nicely and acurately. With hand tools I find that I am MUCH more accurate, and mistakes don't show as easy because the process develops in a controled manner.
![]() ![]() Just this morning I put my first coat of primer on the inside. Above you can see the spaced inwales (and my messy garage).
![]() I have so much going on in my life right now that I know this will be my last solo project for a while, so I am making it very flexible. Like most hybrids it won't be greeat at all, but I have several setups to play with. The main use of this boat will be as a recreational day use kayak. Secondary setup will be as a sliding seat row boat. And third, I would like to add 2 outriggers and sail it like the Hobie Adventure Island. I used the pull saw to bevel some 1x2 to reinforce the stern. I will be adding a Wharram style rudder here that should be fun to make and use. I made a similar bevel for the front to add a bow tie. After the epoxy dries I will trim both flush with the deck.
![]() So what is left at this point? I need to cut and mount the decks. Then fair the bottom and sides. Add the bow and stern ties, as well as drill the holes for rudder mounting. After that, seal with epoxy, prime and paint. At that point It will be ready to use as a kayak. I need to then make the sliding seat rig for
phase 2, and finally I can come up with an outrigger system of akas, leeboard and sailrig for the tri-incarnation. Having a lot of fun at this stage, and still under $115 in materials!
New Project: A Light Sculling Trainer 2 hrs in: Lofting and Cutting 4 hours in: Mistakes Confound and Compound 5 hours now: almost back on track Light sculling trainier on hold ~6 hrs total on the Light sculling trainier: some progress Light sculling trainier: Stitched together! Light sculling trainier: Getting Motivated Sculling trainer: Fiberglass taping started! 2 more hours on the sculling trainer New pics of sculling boat build Sculling boat makes progress Sculling boat has a name and a deck!
|